top of page
Search

7 Ways to Spot Counterfeit Key Blanks Before You Cut

11 minutes ago
10 min read

Last Updated: November 17, 2026

Quick Summary

You can identify counterfeit key blanks by checking that stamps are deep and match the packaging, measuring length, width and thickness with a digital caliper, and test-fitting the uncut blank in the lock cylinder. A blank that binds, rocks or sits loose should be set aside and verified with the manufacturer before cutting.

  • Genuine stamps are pressed deep, while fake or reworked stamps sit shallow and often show grinding marks.

  • A number on the blank that does not match the number on the packet is a simple sign of a repackaged blank.

  • Measure length from shoulder to tip, width at the widest point and blade thickness with a digital caliper.

  • A blank that enters easily but feels loose usually means undersized blade stock that will wear the lock.

  • Do not cut a suspect blank to test it, because that destroys the evidence needed for a return.

Not sure if your key blank is genuine?

We check markings, profile and fit before cutting, so a fake never reaches your lock.

Table of Contents

Why Counterfeit Key Blanks Matter More Than You Think

A counterfeit key blank can cost you far more than the price of a spare.

The problem is that fakes look convincing. Packaging gets copied, stamps get cloned, and online listings rarely tell you where the stock came from.

Below, we break down seven checks you can run before any key meets a cutter. Most take under a minute. Together they help separate genuine stock from copies.

Reading Key Blank Markings: Numbers, Letters and Manufacturer Codes

Genuine blanks carry clear, consistent markings. Counterfeits often carry something close, but not quite right.

Key blank markings are the stamped or engraved codes on the blade or shoulder. They tell you the blank family, the profile, and often the manufacturer. On a genuine blank, these marks sit deep and even. On a fake, they are usually shallow, blurred, or slightly misaligned.

Where to Find the Identification Number

Look on the shoulder, the blade face, or the head of the blank. Common spots include:

  • The flat shoulder just above the blade

  • The side of the blade near the tip

  • The head, often on a recessed panel

If the number on the blank does not match the number on the packet, stop. That mismatch is one of the simplest signs of a reworked or repackaged blank.

Spotting Fake or Reworked Stamps

Reworked stamps are the hardest fakes to catch. Someone takes a cheap blank, grinds off the original mark, and re-stamps it to look like a branded part. A few checks expose this:

  • Depth: Genuine stamps are pressed deep. Fakes sit shallow on the surface.

  • Edges: Look for grinding marks or a slightly dished area around the stamp.

  • Font: Compare letter shapes to a known genuine blank. Fakes often use a different font weight.

If you need to trace a code back to its source, our guide on how to decode a car key code walks through the process step by step.

Key Blank Profile Identification: Matching Shape to Lock Cylinder

Key blank profile identification is where most counterfeits fail. The profile is the cross-section of the blade, and it must match the keyway in the lock cylinder exactly.

Locksmith comparing a high-quality key blank with rough counterfeit key blanks on a workshop bench

Checking Grooves, Shoulder and Tip

Run three quick checks against a known genuine blank:

  • Grooves: Count them and check their spacing. Fakes often have grooves that are slightly too wide or too shallow.

  • Shoulder: The shoulder should be square and clean. A rounded or burred shoulder suggests poor manufacturing.

  • Tip: The tip shape must match. A blunt or uneven tip will not seat properly in the cylinder.

A profile that is close but not exact will cut and turn, then jam. That is how lock cylinders get damaged.

Measuring Dimensions: Length, Width and Thickness Checks

Small differences in size cause big problems. Measure every suspect blank against a genuine one with a digital caliper.

Check three dimensions:

  • Length: From shoulder to tip. Even a fraction of a millimetre off changes how the key seats.

  • Width: Across the blade at its widest point.

  • Thickness: The blade stock itself. Thin stock flexes and wears the lock.

Write the numbers down. If a blank is consistently undersized across several samples, the batch is suspect. Consistent small deviations are a stronger warning sign than one odd blank.

Measure every suspect blank against a genuine one with a digital caliper, checking these three dimensions.

Dimension

Where to measure

Why it matters

Length

From shoulder to tip

A fraction of a millimetre off changes how the key seats

Width

Across the blade at its widest point

Confirms blade stock matches the genuine blank

Thickness

The blade stock itself

Thin stock flexes and wears the lock

Unmarked Key Blank Identification: What to Do When There Are No Codes

Unmarked key blank identification comes down to shape, not stamps. Some legitimate blanks carry no visible code, especially older or generic stock. That does not make them fake, but it does mean you need a repeatable way to decide what to do next rather than guessing.

Work through the decision points below in order. Stop at the first point where the blank fails a check.

Step 1: Decide whether the blank is genuinely unmarked or just worn

Before treating a blank as unmarked, check whether a code has been worn away.

  • Look at the shoulder and blade face under a raking light. A worn stamp often leaves a faint shadow or a slightly polished patch.

  • Check the head for a recessed panel. Many blanks carry the code there, and it is the last area to wear.

  • Compare the wear pattern with the original key. If the original key is also worn smooth in the same place, the blank may simply have seen use.

If you find a partial code, treat it as marked and try to match it before moving on.

Step 2: Classify the blank by profile, not by stamp

With no code to read, the profile is your primary evidence.

  1. Compare the cross-section to a known blank from the same lock. Hold both against a bright background so the groove spacing is visible.

  2. Measure length from shoulder to tip, width at the widest point, and blade thickness with a digital caliper.

  3. Check the shoulder and tip shape. A square shoulder and a clean tip are stronger signs of genuine manufacture than a neat stamp.

  4. Photograph the blank next to a genuine one, side by side, with a ruler in frame. That photograph is your record if the blank later turns out to be wrong.

Step 3: Test-fit without cutting

A test-fit in the lock cylinder, before any cutting, is the cheapest check you have. The blank should enter the keyway smoothly and seat without force. If it binds, rocks, or sits proud of the face, stop.

Watch out: a blank that enters easily but feels loose is as much a warning as one that will not enter. Loose fit usually means undersized blade stock, which will wear the lock.

Step 4: Decide what to do with an uncertain blank

Use this order of preference:

  • If the profile and dimensions match a known genuine blank: treat it as usable, but keep the photograph and measurement record.

  • If the profile matches but the dimensions are consistently small across several samples: treat the batch as suspect and do not cut from it.

  • If the profile is unfamiliar or the blank will not seat: set it aside and verify with the lock or blank manufacturer before cutting.

Step 5: Verify with the manufacturer or a specialist

Appearance alone cannot confirm a blank. Most manufacturers publish profile references and authorised seller lists, and their technical support can confirm whether a given profile is genuine stock. A locksmith who works with the same lock family daily can also compare your blank against known genuine examples. Use that route before you cut anything you are unsure about, it is faster than repairing a damaged cylinder later.

Key Blank Supplier Verification: Checking the Source Before You Buy

Most counterfeits enter through the supply chain, not the cutting bench. Key blank supplier verification is the step that prevents the problem before it starts.

Ask suppliers three questions:

  • Who manufactures the blanks, and can they prove it?

  • What is the returns policy on suspect stock?

  • Can they provide batch documentation?

A supplier who cannot answer these clearly is a risk, however good the price looks. For trade buyers, our guide on buying car key blanks in bulk covers pricing, minimums and vetting in more detail. If you are sourcing stock for the first time, 7 steps to source high-quality blank car keys sets out the full process.

Counterfeit Risks Beyond a Poor Fit

A bad fit is the obvious problem. The hidden risks matter more, and they fall into two groups: what a counterfeit blank can do to the lock, and what it can do to your position as a buyer or installer. Keep the two separate in your own records, because one is a technical claim and the other is a commercial one.

Risks to the lock and the vehicle

  • Cylinder scoring and wafer damage. A blank cut from soft or undersized stock flexes in the keyway. The blade edges then act like a scraper against the cylinder pins or wafers. The first symptom is usually a key that turns with a gritty feel; the second is a key that no longer turns at all.

  • Transponder and immobiliser faults. Cheap chip housings are often moulded slightly oversize or with a weaker plastic. The chip may read intermittently, or the housing may crack and lose contact. Our article on signs your car transponder chip is failing explains the warning signs.

  • Premature wear on the original key. If a counterfeit is used as a spare, the rough blade can wear the lock so that the genuine key also starts to feel loose. That is the point where a cheap spare turns into a lock repair.

Risks to warranty, insurance and your own liability

  • Warranty loss. Work carried out with non-genuine parts may not be covered by the lock or vehicle manufacturer. Check the terms before you fit anything, not after.

  • Insurance and lease conditions. Some fleet and lease agreements require genuine parts for lock and key work. A counterfeit blank can put that cover in question.

  • Trade liability. If you fit a suspect blank for a customer and the lock later fails, the comeback lands on you, not on the supplier who sold the blank.

What to do when you suspect a counterfeit

Do not cut it to "see if it works". That converts a cheap mistake into an expensive lock repair and destroys the evidence you would need for a return.

  1. Stop and isolate. Bag the blank separately from genuine stock so it cannot be picked up by mistake.

  2. Document it. Photograph the blank next to a known genuine one, capture the packaging, and note the supplier, order number and date.

  3. Do not fit it. Test-fitting an uncut blank in the cylinder is acceptable for profile checking; cutting and using it is not.

  4. Contact the seller in writing. State what you found and ask for a replacement or refund. Keep the correspondence.

  5. Escalate if needed. For trade buyers, your supplier contract and any batch documentation are the lever.

  6. Protect the lock. If a suspect blank has already been used, have the lock inspected before further use rather than waiting for a failure.

Watch out: a blank that cuts and turns cleanly once is not proof of quality.

Ask Salisbury Auto Keys to Verify Your Blank Before Cutting

Contact us before anything is cut and we can advise on your blank.

Salisbury Auto Keys is a family-run, RAC-accredited auto locksmith service covering Wiltshire, Hampshire, Dorset and parts of Somerset.

A suspect key blank is a decision point, not a small inconvenience. Get it verified before it is cut, and you protect your lock, your warranty and your day.

Frequently Asked Questions

How can you tell if a key blank is genuine?

Start with the stamped markings. A genuine blank carries a clear manufacturer code and identification number that matches a reference guide. Examine the finish: brass or nickel plating should be even, with no patchy areas or tool marks. Check the profile against the lock cylinder and measure the blade's length, width and thickness. Finally, verify the supplier is an authorized source. If any of these checks fails, treat the blank as suspect and do not cut it.

Can a counterfeit key blank damage a lock?

Yes. Soft or incorrectly machined metal can wear the lock cylinder's pins and wafers, and a profile that is slightly off can jam inside the keyway. Damage often shows up gradually, with the key becoming stiff or the lock failing to turn. Replacing a damaged cylinder costs far more than a genuine blank, so inspect every blank before cutting and stop immediately if it does not slide in smoothly.

How do you identify an unmarked key blank?

Compare the blank physically against a reference guide. Measure the blade length, width and thickness with a caliper, then match the groove pattern, shoulder position and tip shape to known profiles. Photograph the blank next to a ruler for a clear record. If the profile still does not match anything, take it to a locksmith who can verify it against the lock cylinder itself rather than guessing.

Should a locksmith cut a key blank that looks suspicious?

No. A professional should stop and verify the blank first. Cutting a counterfeit blank risks damaging the customer's lock cylinder and voids any warranty on the work. Ask the locksmith to check the markings against a reference guide and confirm the supplier. If the blank cannot be verified, source a genuine replacement from an authorized supplier before any cutting takes place.

 
 
 

Comments


bottom of page